With 18-inch loaded deck height and drop bolsters in the rear at 37-inches tall, this lowboy is ready to haul your equipment under low bridges. The seven position manual ride height adjustment in the rear and five position variable ride height in the gooseneck enable even more deck adjustment based on the load. Haul with confidence thanks to a capacity rating of 110,000 pounds in 12 feet and i-beam cross members on 12-inch centers, and a five year structural warranty.
-
Loads and hauls tall equipment with an 18” deck height
-
Deep well for long booms, no need to detach lower boom section
-
A low rear transition angle lowered bolsters allows for easy loading of equipment over rear deck.
-
Heavy duty outriggers allow loading of heavy wide track units
-
Plenty of tie downs for hard to secure loads
-
D.O.T. approved 12V sealed Grote harness with 7 year warranty
-
Always striving to surpass market standards, all new XL products feature a 5 year structural warranty
-
26’ of well for transporting large equipment
-
XL’s one piece construction results in stronger products. Trailer I-beams are made from one piece web and flange and then welded on all sides
-
1-3/8" raised Apitong decking (center open) is more durable than Oak and stands up to years of wear
-
5 position variable ride height
-
Bucket well provides needed room in the rear bridge
-
Frame reinforcement for a single axle Booster
Back to List
XL 110 Low-Profile HDG: 18" Deck

CAPACITY
GOOSENECK
- 13' Low-Profile Neck with relief cut-out
- 5 position variable ride height
- 51" 5th wheel height
- 110" & 84" SWING CLEARANCE
- 16" & 42" KING PIN SETTING
- HYDRAULICS RUN OFF OF WET KIT
- AIR OPERATED LOCK W/ MANUAL SAFETY LATCH
- brackets for power unit
- work light
MAIN DECK
- 26' LONG
- T-1 Flange, 80k web
- (4) 12" Fully cambered I-BEAMS
- 18" LOADED DECK HEIGHT
- 6" GROUND CLEARANCE
- 8" & 4" stubbed Jr. I-BEAMs ON 12" ALT. CENTERS
- 31" front flip ramps
- (7) BENT D-RINGS PER SIDE
- 1 3/8" APITONG RAISED DECKING - open center
- toolbox in front
- (4) flat-d-rings in toolbox
- (13) chain drops per side
- SWING OUT outriggers on 24" centers
- HEAVY DUTY FLATBACK OUTRIGGERs at front
- BUCKET WELL AT REAR, PLATE ON BOTTOM
- (4) flat d-rings in bucket well
- (2) flag holders
- front ramp upper flange reinforcement
REAR Deck
- 14' LONG
- REAR TRANSITION WITH 32° SLOPE
- 41" LOADED DECK HEIGHT
- OPEN BOOM TROUGH
- OPEN WHEELS WITH BOLSTERS DROPPED 4"
- (1) flat D-rings on main beams at Front
- (1) FLAT D-RINGS ON MAIN BEAMS AT REAR
- (2) chain drops on each bolster
- (2) flag holders
- (2) stake pockets in tail channel for wide load sign
- FRAME REINFORCEMENT FOR booster
|
OVERALL LENGTH & WIDTH
- OVERALL LENGTH: 53'
- OVERALL WIDTH: 102"
SUSPENSION
- 25,000 LB AIR RIDE
- RAISE AND LOWER valve
- MANUAL RIDE HEIGHT control
AXLES
- (3) 25,000 lb NOMINAL
- 54 1/2" AXLE SPACING or 60" Axle SpACING
- air lift on 3rd Axle
- HUB PILOT, OUTBOARD DRUMS
- 16 1/2" x 7" BRAKES
- auto slack adjusters
- LIMIT CHAINS ON ALL AXLES
- SPRING BRAKES ON 1 AXLE
- abs not required
WHEELS & TIRES
- 8.25 x 22.5 STEEL RIMS
- 275/ 70R/ 22.5 H RATED TIRES
LIGHTING
- D.O.T Approved 12V SEALED HARNESS
- RUBBER Mounted led LIGHTS
- (1) MID-TURN SIGNAL per SIDE
- (2) CLEARANCE LIGHTS per SIDE
- 7 POLE ELECTRICAL SOCKET
- 2 TAIL Light package with aluminum cover
PAINT
- 3 YEAR WARRANTY
- BLACK, IH RED, OR NEW CAT YELLOW
- AIR & ELECTRIC DONE AFTER PAINT
- MANY CUSTOM OPTIONS AVAILABLE
|
Back to List
Below are some of the available options for this model. Contact us to find out how to further customize your trailer.
Photos may contain non-standard features.
Back to List
Decking Options

Apitong Decking (Standard)
XL's standard decking is built with Apitong. Apitong is stronger and more resilient than Oak so your deck will hold up to continuous wear.
Photos may contain non-standard features.
Back to List
Back to List
Axle Options

Aluminum Milled Wheels
Aluminum Milled Wheels provide weight savings, as they are 27 lb lighter than standard steel.
Photos may contain non-standard features.
Back to List
Back to List
Ramp Options

Mechanical Ramp (Standard)
The standard Mechanical Ramp is used for loading onto mechanical trailers.
Photos may contain non-standard features.
Back to List
Back to List
Outrigger Options

Flat Back Outriggers
XL offers a wide range of tie down options to fit your preference and needs. Flat Back Outriggers are one option.
Photos may contain non-standard features.
Back to List
Back to List
Lighting Options

LED 2 Tail Light Package (Standard)
The 2 Tail Light Package is the standard on XL products. XL tail lights feature rubber mounted LED lights.
Photos may contain non-standard features.
Back to List
Back to List
Tie Down Options

Bent D-Rings (Standard)
XL offers a wide range of tie down options to fit your preference and needs. The Bent D-Rings are the standard.
Photos may contain non-standard features.
Back to List
Back to List
Sign Options

Oversize Load Sign
The Oversize Load Signs increases safety by alerting others of the trailers' load.
Photos may contain non-standard features.
Back to List
Back to List
Paint Options

Black Paint (Standard)
Black paint is one of XL's standard color options.
Photos may contain non-standard features.
Back to List
Back to List
Suspension Options

Air Weigh Scale
The Air Weigh Scale digitally reads the loaded weight on each axle, making accurate loading more efficient.
Photos may contain non-standard features.
Back to List
Back to List
Gooseneck Options

13HP Honda Unit Top of Neck
This option allows you to place the 13HP Honda Unit on the top of the neck. It features dual hydraulics.
Photos may contain non-standard features.
Back to List